Easifringe Human Hair Clip in Bangs

$375.96
(No reviews yet) Write a Review
Easifringe Human Hair Clip in Bangs

Topper Collection by Jon Renau/EasiHair
Human Hair Mono Clip-In Fringe

Fiber Type: Remy Human Hair 
Base Construction: Monofilament, Machine Weft 
Base Dimension: Base 6.5" x 3"
Application Method: Clip In 

Stage of Hair Loss: Beginning Stage


Length: 7.5" - 12"
Weight: 1.9 oz

Color Shown: Pic 1-3: 6RN 
Bang out a new look! This 100% human hair clip in bangs piece can be custom cut and heat styled to create any look and blend with any hair texture. With this single accessory, you can instantly add side swept layers to thicken your hairline or slice a blunt edge for a new style without the commitment of a cut.

Care For Hair

We recommend washing your wig every 6-8 wears

CLEANSE & CONDITION

  • Before washing your HD wig or hairpiece, gently remove any tangles with your Jon Renau wide tooth comb ONLY

  • Hold wig or hairpiece under cool running water.

  • Gently lather the hair with a capful of Shampoo while making sure that the hair is traveling in the same direction. DO NOT rub hair as this may cause tangling

  • Rinse thoroughly in cool water until the water runs clear

  • Wrap wig or hairpiece in a towel and gently pat dry

  • Gently detangle hair using your Jon Renau wide tooth comb

  • Spray with Leave-In Conditioning Spray (3-5 pumps) keeping away from base of wig or hairpiece

CURL

  • Heat your curling iron to 270°-280° F

  • Using your Jon Renau wide tooth comb, gently comb hair free of tangles

  • Starting at the nape, take ½ inch-1.5 inch sections of hair (Smaller sections=tighter curls, larger sections=looser curls)

  • Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

  • Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig or hairpiece, staying 1-2 inches away

  • Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand

  • Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl)

  • Allow curl to cool completely (about 5 minutes); remove clip and let curl hang naturally

  • Hair can be combed with your Jon Renau wide tooth comb (or fingers for best results) to blend curls

DRY & STYLE

  • Air drying your wig will give the best results. You can gently blow dry (low-medium heat) using ONLY your Jon Renau wide tooth comb

  • Apply HD Smooth Detangling Spray, (3-5 pumps) focusing on the bottom half of wig or hairpiece. Gently comb through again with your Jon Renau wide tooth comb

  • We recommend that ONLY the Jon Renau wide tooth comb is used on your HD wig or hairpiece. Other tools will cause frizzing/tangling

  • HD Fiber can withstand heat tools up to 350° F, however, Jon Renau recommends working at 270°-280° F

  • It is recommended to use professional grade heat styling tools with digital temperature settings to control heat

FLAT IRON

  • Heat your flat iron to 270°-280° F

  • Starting at the nape, take ½ inch-1.5 inch sections

  • Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

  • Staying at least 1-2 inches away from base, slowly smooth flat iron down through ends

  • Keep hair smooth by following behind the flat iron with your Jon Renau wide tooth comb

  • Allow hair to hang naturally and cool completely

TIPS

  • We recommend using HD Smooth Detangling Spray with a Jon Renau wide tooth comb DAILY to detangle your HD wig. This is especially important with the mid-length to long length HD wigs or hairpieces

  • We offer HD Smooth in a convenient 2oz. size for travel

  • Allow your HD wig to air dry naturally instead of blow drying to help maintain the integrity of the fiber

  • Help protect the fiber against heat damage by using Heat Treat Thermal Spray when using heat styling tools